Fiber cement siding is known for being low maintenance, but low maintenance is not the same as no maintenance. A little attention each year keeps the finish looking good, keeps water out of the wall, and catches small problems before they turn into repairs.
This guide pulls together what James Hardie, the best-known fiber cement brand, publishes about caring for its siding: how to clean it, what to avoid, how caulk and paint fit in, and what to check when you walk around the house. If your home has a different brand of fiber cement, follow that manufacturer’s instructions, since details can differ.
How often to clean fiber cement siding
James Hardie recommends cleaning its siding once or twice a year, and its cleaning guide suggests hosing the siding down every 6 to 12 months. The company also notes that maintenance needs depend on where you live and how exposed the building is. A wall that faces heavy weather, sits under trees or stays shaded and damp will usually need more attention than a sunny, sheltered one.
The right way to clean it
The basic method is simple. James Hardie recommends a low-pressure spray from a garden hose and a soft, medium-bristle (non-metal) brush to remove dirt and debris.
Everyday dirt and dust
- Brush the surface dirt off with a soft brush, then rinse with the garden hose.
- If you use a cloth, wipe side to side in the direction of the plank, shingle or panel.
- Work one small section at a time, starting at the top and working down, so dirty water does not drip onto areas you have already cleaned.
Grease, oil and other stains
For oily or organic stains, James Hardie suggests a soft cloth with mild liquid dish soap and water, rinsing the cloth often, then rinsing the wall with the hose. Do not let soap dry on the siding. Keep rinsing until all of it is gone.
Mold and mildew
Mildew can look a lot like dirt, so look closely, especially on shaded walls. James Hardie’s guidance is to lightly scrub the area with a soft cloth or sponge and a mildew-specific cleaner, follow the cleaner’s label instructions, wear any protective equipment the label calls for, and rinse with the hose.
What not to do
Most damage to fiber cement finishes comes from cleaning too hard. According to James Hardie:
- Do not use a pressure washer. The company says a pressure washer can damage the surface of its siding, and its cleaning guide says not to use a high-pressure power washer.
- Do not use a hard metal brush or an abrasive sponge. These can damage the finish.
- Do not use harsh chemicals such as bleach or acid.
Caulk: check it, and know where it does not belong
Caulk is one of the first things to look at during an inspection. James Hardie’s FAQ recommends inspecting the caulk around the edges of your home and repairing it if it fails. Its winter maintenance tips add that damaged areas should be repaired, re-caulked or replaced to keep moisture from getting behind the siding.
When caulk does need replacing, James Hardie’s installation documents call for a sealant that meets ASTM C920 (Grade NS, Class 25 or higher) or a latex joint sealant that meets ASTM C834, applied according to the caulk maker’s instructions.
Just as important is where caulk should not go. James Hardie’s quick start installation guide marks several spots “Do NOT caulk,” including the gap above horizontal flashing and joint flashing behind butt joints. Those gaps are there on purpose so water that gets behind the siding can drain out. Filling them can trap water. If you are unsure whether a gap should be sealed, ask before you caulk it. For siding with the factory ColorPlus finish, James Hardie also says not to caulk nail heads; those are handled with touch-up instead.
Paint: factory finish vs. field-painted siding
How you care for the color depends on how the siding was finished.
Factory-finished (ColorPlus Technology)
James Hardie’s ColorPlus siding comes from the factory already painted. The company says its finishes are UV-resistant and that ColorPlus finishes carry a 15-year limited warranty covering paint and labor against peeling, cracking and chipping (terms per James Hardie; read the actual warranty for your product). For small nicks and scrapes, James Hardie sells color-matched touch-up kits. Its quick start guide says touch-up pens are for nail heads and very small nicks and scratches smaller than a dime; if the damaged area is larger than that, the piece should be replaced with a new plank or panel rather than touched up. James Hardie also notes that it does not warrant third-party touch-up paint on ColorPlus products.
Factory-finished siding can still be repainted later if you want a new color. For repainting ColorPlus siding, James Hardie’s installation instructions recommend a clean, dry surface free of dust, dirt and mildew, say repriming is normally not necessary, and recommend 100% acrylic topcoats.
Primed siding painted on site
If your siding was installed primed and painted on site, the paint is what protects it. James Hardie’s FAQ says pre-primed siding should get an acrylic topcoat, and its installation instructions recommend 100% acrylic topcoats and say not to use stain, oil/alkyd-based paint or powder coating on its products. The same instructions say primed product must be painted within 180 days of installation, and that siding should not be painted when wet.
Between paint jobs, James Hardie’s winter tips recommend touching up any peeling or cracked paint so moisture cannot get at the siding during cold months. Keeping the siding clean also helps, since the company notes cleaning prevents build-up that can lead to paint deterioration.
Clearances: keep the bottom edges dry
Fiber cement is installed with gaps between the siding and the surfaces around it. James Hardie’s quick start installation guide (U.S.) shows these minimums:
- 6 inches between the siding and the ground
- 2 inches between the siding and slabs, paths and steps
- 2 inches between the siding and a deck surface
- 2 inches between the siding and a roof where a wall meets it
- 1 inch between the siding and a gutter
- Kick-out flashing (at least 4 by 4 inches) where a roof edge meets a wall
These are installation requirements, but they matter to homeowners because clearances shrink over time. New mulch beds, raised soil, a new patio or a deck rebuilt higher can all close the gap. When you look around the house, check that soil and mulch have not crept up toward the bottom course, and that the ground still slopes away from the wall. Local building codes and the current James Hardie instructions for your product take precedence.
A simple inspection checklist
Once or twice a year, often when you clean, walk around the house and look for:
- Cracks, gaps or loose siding pieces
- Caulk that has cracked, shrunk or pulled away, especially around windows, doors and trim
- Small cracks, chips and dents. James Hardie says these can be repaired with a cementitious patching compound.
- Peeling or cracked paint on field-painted siding
- Mildew on shaded or damp walls
- Soil, mulch or hard surfaces that have built up against the bottom edge
- Overflowing or clogged gutters. James Hardie notes clogged gutters can overflow, which puts extra water on the walls below. Our guide on when to replace gutters covers what to look for.
If you are still deciding between materials, our comparison of James Hardie vs. vinyl siding covers how the two differ.
Frequently asked questions
Can I pressure wash James Hardie siding?
James Hardie says a pressure washer can damage the surface of its siding. It recommends a low-pressure spray from a garden hose and a soft, medium-bristle brush instead.
How often should fiber cement siding be cleaned?
James Hardie recommends cleaning once or twice a year, about every 6 to 12 months. Walls with more weather exposure or shade may need it more often.
Should I caulk every gap in my fiber cement siding?
No. Caulk around trim, windows and doors should be inspected and repaired when it fails, but James Hardie’s installation guide marks some gaps, such as the space above horizontal flashing, as “Do NOT caulk” so water can drain. Ask a professional if you are not sure.
Can factory-finished ColorPlus siding be repainted?
Yes. James Hardie says ColorPlus siding can be repainted if you want a new color. Its instructions recommend a clean, dry surface and 100% acrylic topcoats, and say not to use stain or oil/alkyd-based paint.
If your fiber cement siding has damaged boards, failing caulk or clearance problems, we can take a look and explain your options. Learn more about our fiber cement siding work, or request a free estimate. You can also read James Hardie’s own siding cleaning guide.
