Serving Bucks & Montgomery Counties, Southeastern Pennsylvania and nearby New JerseyServing Southeastern PA & nearby NJMon–Fri 8am–8pm · Sat 8am–2pm · Customer Login

Roof Flashing: Where Most Roof Leaks Start and How to Spot Problems

Roof Flashing: Where Most Roof Leaks Start and How to Spot Problems

Many roof leaks start where the roof meets a chimney, wall, valley or pipe. Here is how each type of flashing works, the warning signs, and how to decide between repair and replacement.

Estimated Read Time:

Share:

Shingle roof with dormers

When a roof leaks, the shingles often get the blame. In many cases, though, the water is getting in somewhere the roof meets something else: a chimney, a wall, a valley or a pipe sticking through the roof. Those joints are sealed with flashing, and federal building-science guidance counts these joints among the most vulnerable spots on a roof for water to get in.

This guide explains what flashing does, where it is used on a typical home, the signs it may be failing, and how to think about repairing it versus replacing it along with the roof.

What flashing does

Flashing is usually thin metal (sometimes combined with membranes or rubber collars) that directs water away from joints and openings and back onto the roof surface or into the gutter. Pennsylvania’s adopted residential code (the 2018 International Residential Code, Section R903.2) says flashing must be installed in a way that prevents moisture from entering the wall and roof, and requires it at wall and roof intersections, wherever the roof changes slope or direction, and around roof openings.

The U.S. Department of Energy’s Building America Solution Center puts it simply: roof penetrations are a weak spot in the roof’s armor where water could leak into the building.

The five places to check

1. Chimneys

Chimneys get several kinds of flashing. Along the sides, step flashing is woven in with the shingles. Above it, counterflashing is embedded into a mortar joint in the brick and laps down over the step flashing, as shown in the Building America Solution Center’s guidance on flashing penetrations. On wider chimneys, the code also requires a cricket or saddle, a small peaked section on the uphill (ridge) side that steers water around the chimney. Under the 2018 IRC (Section R903.2.2), that applies to chimneys and penetrations more than 30 inches wide, measured across the slope.

2. Step flashing where a roof meets a wall

Where a sloped roof runs alongside a wall, such as at a dormer or a second-story wall above a garage roof, the code calls for base flashing that is continuous or step flashing, directing water away from the wall onto the roof or into the gutter. The Building America Solution Center describes step flashing as L-shaped metal pieces bent at a right angle, with one half against the wall and the other woven in with the shingles. It should sit under the siding, not over it.

3. Kick-out flashing

At the bottom of a roof-to-wall joint, where the roof edge ends against the wall, a kick-out flashing turns water away from the wall and usually into the gutter. Without one, water can run straight down the wall. The Building America Solution Center notes that siding such as fiber cement, vinyl and brick veneer can mask the evidence of this kind of leak for years, and that kick-out pieces bent from sheet metal in the field are often too small to work. Missing kick-outs are a frequent concern on stucco homes as well; see our article on stucco moisture problems in Pennsylvania.

4. Valleys

A valley is the channel where two roof slopes meet, and it carries a lot of water. The Building America Solution Center calls valleys and roof penetrations among the most vulnerable areas for water intrusion. It recommends a self-sealing membrane under the roofing in the valley, and notes that on shingle roofs, metal valleys are recommended over woven or abutted shingles. Under the 2018 IRC, valley linings must be installed according to the shingle manufacturer’s instructions before shingles go on.

5. Pipe boots and other penetrations

Plumbing vents, exhaust fans and flues all pass through the roof. Most are sealed with a pre-made collar, often called a pipe boot. Owens Corning notes that some vent pipes are sealed with a rubberized gasket, and that over time the gasket or the sealant around it can dry out and fall apart. Building America adds that caulk or roofing sealant is not a substitute for proper flashing.

Signs your flashing may be failing

You do not need to climb on the roof to spot many warning signs. Owens Corning suggests finding a safe vantage point, such as a second-story window, and calling a roofing contractor if you see flashing that is rusted, dented, missing fasteners, or has sealant that is rotting away. Other clues:

  • Ceiling or wall stains near a chimney, skylight, dormer or bathroom vent.
  • Streaks or stains on the siding below a roof-to-wall joint. Building America notes this can also mean a gutter is overflowing.
  • Peeling or bubbling paint, warped siding, or soft trim on walls next to a lower roof. Building America says these are signs of moisture that should be investigated, and that wood that feels spongy when pressed with a screwdriver is likely water-damaged.
  • Heavy caulk or tar smeared around a chimney or pipe instead of metal flashing.
  • Dried-out or crumbling rubber around plumbing vent pipes.

Our roof leak repair page explains how we track down where water is getting in.

Repair or replace?

The Building America Solution Center’s guidance for existing homes is to repair or replace missing, damaged or poorly installed flashing at all roof penetrations, after checking the roof and framing underneath and fixing any damage first.

A repair often makes sense when

  • The problem is limited to one spot, like a single pipe boot or a short section of chimney counterflashing.
  • The shingles around it are in good shape and have plenty of life left.
  • There is no rot in the roof deck or wall below.

A bigger job may be needed when

  • Step flashing at a wall is missing or failed. Building America notes that fixing this properly can mean removing siding to expose at least 8 inches of the wall.
  • Water has already damaged sheathing, framing or wall materials.
  • The roof itself is near the end of its life. Building America recommends that when the roofing on an older home is replaced, all of the flashing at penetrations, roof-wall joints and valleys be inspected at the same time.

If you are planning a roof replacement, ask how the quote handles flashing: what will be replaced, what will be reused, and whether kick-outs and crickets are included where needed.

Frequently asked questions

Can flashing be fixed with caulk?

Not as a permanent fix. The Building America Solution Center says caulk or roofing sealant is not a substitute for proper flashing, and vents that rely only on caulk need regular inspection.

What is kick-out flashing?

It is a flashing piece at the bottom of a roof-to-wall joint that turns water away from the wall and into the gutter. Without it, water can run down and into the wall, and some siding types can hide the damage for years.

Should flashing be replaced when I get a new roof?

The Building America Solution Center recommends inspecting all flashing at penetrations, roof-wall joints and valleys whenever an older roof is replaced. Ask your contractor which pieces will be replaced and which will be reused.

How can I check my flashing safely?

Owens Corning suggests looking from a safe vantage point, such as a second-story window, and calling a roofing contractor if you see rust, dents, missing fasteners or failing sealant. Do not walk on the roof yourself.

If you have a leak near a chimney, wall or vent pipe, we can inspect the flashing and tell you honestly whether a repair will do. Learn more about our roof flashing repair or request a free estimate. For more background, see the Building America guide to missing roof and wall flashing.

Other Posts